点击图片查看原图
Summit NGP Series lubricants are formulated from highly refined paraffinic petroleum base stocks and the unique additive Syntholate. The refining process includes catalytic hydrogenation to remove impurities, M.E.K. solvent dewaxing to provide low pour points and vacuum distillation to assure low vapor pressure. The addition of Syntholate inhibits the formation of varnish and carbon and provides superior thermal and oxidative stability. Utilizing the superior petroleum base stocks fortified with Syntholate extends the life of Summit NGP Series lubricants compared to that of conventional mineral oils and provides the following money saving benefits:
* Reduces lubricant consumption - Extended drain intervals and lower vapor pressures reduce lubricant consumption.
* Reduces maintenance - Reduces carbon and varnish formation thus extending the time interval between overhauls.
* Excellent lubricity - Provides improved wear protection for bearings and other moving parts.
* Good compatibility - The base stocks and special additive package provide excellent compatibility with system components and inhibit against hydrogen sulfide corrosion.
* Improves safety - Higher flash points provide a greater margin of safety.
Summit NGP Series lubricants with Syntholate pay for themselves with the first lubricant change.
Available as: NGP-100, NGP-150
Top of page
NGSH
Summit NGSH Series lubricants are formulated from the highest quality synthetic hydrocarbon base stocks. NGSH lubricants are extended life fluids with special additives to protect equipment from wear, rust and hydrogen sulfide corrosion. These fluids are designed for rotary screw and reciprocating compressors in natural gas service. Summit NGSH Series lubricants are compatible with commonly used seal materials and equipment designed for use with petroleum oils.
Available as: NGSH-68, NGSH-100, NGSH-150, NGSH-220
Top of page
PGS-2
Summit PGS-2 synthetic lubricant is a polyglycol-based product for use in enclosed gears, bearings, and compressors wher conditions demand the unique properties of this fluid. Better wear protection, thermal and oxidation stability, and reduced sludge and deposit formation insure enhanced performance when compared to petroleum-based lubricants.
When used in gas compression applications, the resistance to thinning out by hydrocarbon dilution allows PGS-2 to maintain the proper operating viscosity, extending drain intervals and parts life. Due to the varying make-up of gases and operating temperatures, please contact your Summit representative for specific product recommendations.
· As the PGS-2 lubricant is incompatible with petroleum oils, care should also be taken to make sure the two are not mixed.
Top of page
PGS
Summit PGS synthetic lubricants are polyglycol-based products for use in enclosed gear, bearings, and compressors wher conditions demand the unique properties of these fluids. Better wear protection, thermal and oxidation stability, and reduced sludge and deposit formation insure enhanced performance when compared to petroleum-based lubricants.
When used in gas compression applications, the resistance to thinning out by hydrocarbon dilution allows PGS to maintain the proper operating viscosity, extending drain intervals and parts life. Due to the varying make-up of gases and operating temperatures, please contact Summit for specific product recommendations.
· As the PGS lubricants are incompatible with petroleum oils, care should also be taken to make sure the two are not mixed.
APPLICATIONS
· Enclosed Gears
· Bearings
· Natural Gas Compressors
· General Lubrication
Available as: PGS-68, PGS-100, PGS-150
Top of page
PGI
Summit PGI synthetic lubricants were designed for use in the compression of propane as well as many natural gas applications. Available in three grades for rotary screw and reciprocating compressors, PGI is especially suitable for wet gas situations. Due to the varying make-up of gases and operating temperatures, please contact Summit for specific product recommendations.
Available as: PGI 68, PGI 100, PGI 150
Top of page
NGL Series
The lubricant problems generally encountered with the compression of natural gas and CO2 are related to the reaction of the gas stream with the lubricant. These include:
• Solubility of gas in the lubricant causes reduced lubricant viscosity resulting in cylinder scoring and high wear rates. Compensating for this with a higher iscosity lubricant can cause handling problems at lower temperatures.
• Absorption of lubricant into the gas stream results in high lubricant usage rates and a depletion of protective lubricant film in the cylinder.
• Condensed hydrocarbon liquids in the cylinder area can "wash" the lubricant from the cylinder walls causing severe mechanical damage.
• The carryover from increased lubricant feed rates or use of heavily compounded oils to compensate for hydrocarbon and CO2 dilution and wash-out can damage the well formation and plug CO2 injectors.
• Gases such as CO2 and H2S may be corrosive to compressor components. NGL protects against the corrosive effect of these gases to compressor components while maintaining lubricating properties.
Summit NGL Series polyalkylene glycol lubricants were formulated to combat these problems associated with high pressure reciprocating compressors pumping natural gas, carbon dioxide, or process gases. NGL Series lubricants are extremely resistant to hydrocarbon and CO2 dilution and absorption of the gas stream components. Any lubricant carryover will not impair the well formation as it is compatible with well-bore treatment fluids and soluble in water. The result is a lubricant maintaining the proper viscosity for wear protection, resisting wash-out and carryover, and posing no threat of damage to the well formation or CO2 injectors.
The extremely high viscosity index of the NGL Series lubricants allows protection over a broad temperature range. The low pour point provides all-season ease of handling even in very cold climates. The use of pressurized and heated tanks as well as heat traced lines can be eliminated.
Summit NGL Series can offer these same advantages when compressing a number of other difficult gases including hydrogen, helium and nitrogen. Please contact your Summit representative with your specific gas application.
Top of page
DSL®-XM
Summit DSL®-100XM is formulated from the best diester base stocks available and employs state of the art additive technology to provide an outstanding lubricant. DSL®-100XM contains no metals and is specially formulated for use in process gas applications involving catalytic processes. DSL®-100XM is approved by U.O.P. for hydrogen compressor service associated with their catalytic processes.
Summit DSL®-100XM is recommended for use in the following applications:
· Centrifugal compressors Rotary screw and vane compressors
· Reciprocating compressors Ball and roller bearings
· Low temperature lubrication General lubrication
· High temperature lubrication Air tool lubrication
· Mist lubrication systems
Top of page
SH®-32T and SH®-46T
Summit SH®-32T and SH®-46T Gas Turbine Lubricants have been formulated to operate in land-based gas turbines under a wide range of temperatures. Synthetic hydrocarbon base stocks and selected additives combine to provide excellent viscosity-temperature characteristics, oxidation stability, wear resistance, and load-carrying ability.
Summit Gas Turbine Lubricants meet the requirements of specifications approved by all of the major manufacturers of gas turbines and Summit SH®-32T is approved by Solar Turbine as conforming to their ES9-224 lube oil specification for Class I ISO 32 lube oils.
Top of page
LCG-Series
LCG Series are specially formulated compressor lubricants designed to be inert to reactive and corrosive gases encountered in landfills, refineries, EOR and chemical process plants. LCG Series is based on 100 % pure synthetic PAO. It’s extremely low vapor pressure results in minimal carryover past the separator. It does not contain sulfur or other impurities associated with petroleum based products that might react with the acids, chlorinated compounds or sour gases found in various applications. PAOs are fully saturated compounds and do not contain the alkenes or aromatics found in group I, II or even the group III mineral oils touted as being "pure." LCG Series is ester free and not subject to hydrolysis issues encountered with most esters when used in acidic environments. LCG Series is suitable for use in certain chloride containing environments wher the use of mineral oil, esters or synthetic polyglycols (PAGs) are not permitted. Lubricants that are reactive with a gas stream may form by-products that are harmful to equipment or the environment. Solids may form and cause fouling or plugging issues in certain applications.
LCG Series will protect oil wetted parts against the corrosive effects of common acids and water. It is engineered with superior technology to inhibit the effects of sour gases such as hydrogen sulfide or carbon dioxide on metal surfaces found within the oil wetted parts of a compressor.
LCG Series is designed to result in longer fluid and equipment life for rotating compressors in corrosive and reactive environments. Please consult with a Summit Industrial Products lubrication expert about the suitability of LCG Series in these types of applications.
jAvailable as: LCG- 68 and LCG-100
Top of page
The information contained in this document is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability.
电话：158 4195 5870（李莹） QQ:191 948 7228
电话：158 4195 5870（李莹） QQ:191 948 7228